Stick Drift Test
This stick drift test measures how far each analog stick sits from its centre while you are not touching it. You get the number, a verdict and a deadzone that would hide it.
Press any button on your controller to start.
- Position
- X 0.000 · Y 0.000
- Rest offset
- —
- Suggested deadzone
- —
- Circularity error
- —
- Position
- X 0.000 · Y 0.000
- Rest offset
- —
- Suggested deadzone
- —
- Circularity error
- —
How to run the stick drift test
- Let go of both sticks. With your controller connected, put it down on a table so nothing touches the caps.
- Press Measure and wait. For five seconds the page records every position each stick reports while it rests.
- Roll each stick in circles. Start the circularity part and make three slow laps around the edge.
A stick drift tester is the fastest way to settle an argument with a game: if the rest offset reads zero here, the stick is not what moves your camera. If the game still feels late, try the controller polling rate test. If the page cannot see your controller at all, the controller tester page has the checklist.
What your numbers mean
| Rest offset | Verdict | What you notice in games |
|---|---|---|
| 0.00 to 0.05 | Normal | Nothing. A default deadzone hides this much. |
| 0.05 to 0.10 | Borderline | Slow camera or cursor creep where the deadzone is small. |
| Above 0.10 | Drift | Your aim or your character moves on its own. |
The stick drift test gives each stick one of these three verdicts. It also suggests a deadzone: the smallest setting that covers the offset it measured, plus a little headroom. Controller drift that needs a deadzone above 0.15 is usually better repaired than hidden, because that much dead travel costs you fine aim.
What is stick drift?
Stick drift is input that a controller sends while nobody is touching the stick. The game sees a small, steady push in one direction.
- Wear Most sticks read their position with a wiper that slides over a carbon track. The track wears thin where the stick rests.
- Dust Grit inside the module lifts the wiper or bridges the track, so the reading jumps.
- A shifted centre A tired spring or a hard knock leaves the stick resting away from the middle it was calibrated to.
Sticks built on Hall effect or TMR sensors have no track to wear, which is why they rarely drift.
How to fix stick drift
Go from the easy steps to the hard ones.
- Reconnect it. Unplug or unpair the controller, switch it off and connect again without touching the sticks. A bad centre reading at power-on looks exactly like drift.
- Raise the deadzone. Set it to the suggested value in the game, or in Steam for games that have no setting.
- Clean around the stick. With the controller off, blow compressed air under the cap while you rotate it.
- Recalibrate. Windows, Steam and some consoles have a calibration screen that stores a new centre.
- Replace the module. If the offset stays above 0.10, the part is worn. Try the warranty first: on most controllers a new module has to be soldered in.
A stick drift fix only counts if the number drops, so measure again after every step.
Stick drift on PS5, Xbox and Switch controllers
- PS5 The console has no deadzone setting for the standard DualSense, so drift shows up in every game. Plug the controller into a computer and you have a ps5 stick drift test that shows the real offset.
- Xbox The Xbox Accessories app can recalibrate the sticks of current controllers. Measure here before and after to see whether it helped.
- Switch The console has its own Calibrate Control Sticks screen. A Pro Controller connects to a computer over Bluetooth for this controller drift test.
Deadzone and circularity
A deadzone is a small area around the centre where the game ignores the stick. It hides drift, and it costs you the first few degrees of movement. The plot draws the suggested deadzone as a shaded circle, which turns this page into a controller deadzone test: you can see how much travel the setting would eat.
Circularity is how close the stick's outer edge is to a perfect circle. The circularity test reports the average error. A flat side or a dent in the outline means the stick does not reach full tilt in that direction. Run it right after the stick drift test, while the controller is still on the table.
More controller tests
Frequently asked questions
Is a small offset normal on a new controller?
Yes. Almost no stick rests at exactly 0.000. A reading under 0.05 on a new controller is not a fault, and a stick drift checker should not flag it.
Should I put the controller down while it measures?
It helps. A thumb on the cap or a tilted grip can move a stick enough to change the result. A table gives the cleanest reading.
Can stick drift go away on its own?
Sometimes, if dust caused it and the dust has moved. Drift from a worn track comes back and slowly gets worse.
How accurate is this stick drift test?
It shows what the controller reports to your computer, to three decimal places. Some controllers apply a small deadzone of their own before they send anything, so a perfect zero can hide a very small offset.